1CH 1000M DC RF Long Range Remote Control Electrical Switch 315MHz / 433MHz

Description

0020527
1CH  1000M DC RF Long Range Remote Control Electrical  Switch 315MHz / 433MHz
Model: 0020207
Package  Include:
1 x Receiver: S1U-DC06-ANT1 / S1U-DC09-ANT1 /  S1U-DC12-ANT1 / S1U-DC24-ANT1 (1 Channel / Three Control Modes)
1 x Transmitter: CB-2
1 x User manual
Feature:
Application: It can be used in industry  automation, agriculture automation and home automation, such as factory, house,  farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call,  etc. It can remote control equipments on land, water and air, such as remote  control lights, sirens, locks, motors, fans, winches, blinds, linear actuators,  doors, windows, electric solenoid valves, security alarm, business signs and  various devices.
Wireless control, easy to install.
Relay Output: This receiver is relay output,  it can be used to operate both DC and AC equipments. The terminal is NO / NC  (normally open / normally closed), which serves as a switch. That means you  should also connect a separate power supply to it.
Each channel can work at maximum current 10A,  such as 120W/12V, 60W/6V, 90W/9V, 240W/24V, 1100W/110V, 2200W/220V.
With wired control terminals: You can connect  sensors, limit switches, manual switches or external devices to control the  receiver.
Design with low-power and high-speed CMOS  technology.
You can turn on/ off the receiver with  transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls,  floors, doors or windows.
With reverse power protection and over current  protection.
Reliable control: The receiver only works with  the transmitter which use same code.
One/several transmitters can control  one/several receivers simultaneously.
You can use two or more units in the same  place.
Receiver:
Model No. S1U-DC06-ANT1 / S1U-DC09-ANT1 / S1U-DC12-ANT1 /  S1U-DC24-ANT1
Power Supply (Operating  Voltage): DC6V (S1U-DC06-ANT1), DC9V±1V (S1U-DC09-ANT1), DC12V±1V  (S1U-DC12-ANT1), DC24V±1V (S1U-DC24-ANT1)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of  Relay: AC110~240V or DC0~28V
Working Frequency: 315MHz  / 433MHz
Channel: 1CH
Control Modes: Toggle, Momentary, Latched
Static Current: ≤6mA
Maximum Working Current:  10A / each channel
PCB size: 67mm x 50mm x 18mm
Case size: 75mm x 54mm x 27mm
Work with Fixed code transmitters or Learning code transmitters.
Length of External Telescopic Antenna: 80mm / 305mm (stretch)
The receiver has farther working range with external telescopic  antenna.
Transmitter:
Model No.: 0021024 (CB-2)
Channel/Button: 2
Button Symbol: big button, small button
Operating Voltage: 9V (1  x 6F22 -9V battery, can be used for 12 months)
Operating Current: 30mA
Operating Frequency:  315Mhz / 433Mhz
Encoding Chip: PT2262 / PT2264 / SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance:  1000m / 3000ft (theoretically)
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 135mm x 42mm x 25mm
Weight: 95g
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit  board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “L” side, and the lower row of pads  is “H” side.
3. If solder the middle row of chip feet to the “L” side, it is  code 1. If solder the middle row of chip feet to the “H” side, it is code 2.  Don’t solder to any side, it is code 0.
4. The 8-bits code order is from left to right (from A1 to A8).
5. Here is an example, the 8-bits code in the picture is  00010121, solder as the following way:
6. Code 0: don’t solder any side, like A1、A2、A3、A5.
7. Code 1: solder to the “L” side, like A4、A6、A8.
8. Code 2: solder to the “H” side, like A7.
Matching Transmitters:
The receiver can work with different  transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof),  CP-1 / CP-2 (500M), or CB-1 / CB-2 (1000M) etc.
When you set the receiver in toggle or  momentary mode, it should work with single button transmitter, such as model C-1  (100M), CWB-1 (50M, waterproof), CP-1 (500M), or CB-1 (1000M) etc. When you set  the receiver in latched mode, it should work with two buttons transmitter, such  as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2 (500M), or CB-2  (1000M) etc.
Working Range:
With a transmitter (such as C-2) to form a  complete set, the maximum working distance can reach 100M in an open ground.
The maximum working distance is a theoretical  data, it shall be operated in an open ground, no barriers, no any interference.  But in the practice, it will be hindered by trees, walls or other constructions,  and will be interfered by other wireless signals. Therefore, the actual distance  may not reach this maximum working distance.
Usage (with the transmitter like C-2):
The receiver can be used to control both DC  0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not  DC/AC power output. Initial state of relay output terminals: Terminals B and C  are Normally Open; Terminals A and B are Normally Closed.
Wiring:
If you want to control a DC 12V lamp, do as  following:
1) Connect the positive pole of DC power supply to terminal “L / +” of INPUT,  and connect the negative pole of DC power supply to terminal “N / -” of INPUT.
2) Connect terminal C to the positive pole of DC power supply, connect terminal  B to the positive pole of DC lamp, and connect the negative pole of DC lamp to  the negative pole of DC power supply.
If you want to control an AC 220V lamp, do  as following:
1) Connect the positive pole of DC power supply to terminal “L / +” of INPUT,  and connect the negative pole of DC power supply to terminal “N / -” of INPUT.
2) Connect terminal C to the live wire of AC power supply, connect terminal B to  one side of AC lamp, and connect another side of AC lamp to the neutral wire of  AC power supply.
Setting different control modes:
Setting different  control modes (We have set the receiver as Toggle control mode before delivery.  If you want to use other control modes, do as following operation):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle: Press -> On; Press again -> Off.
Press button 1: Turn on the relay (connect B and C, disconnect A and B), the  lamp 1 is on.
Press button 1 again: Turn off the relay (disconnect B and C, connect A and B),  the lamp 1 is off
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on the relay (connect B and C, disconnect A and  B), the lamp 1 is on.
Release button 1: Turn off the relay (disconnect B and C, connect A and B), the  lamp 1 is off
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button ->  Off.
Press button 1: Turn on the relay (connect B and C, disconnect A and B), the  lamp 1 is on.
Press button 2: Turn off the relay (disconnect B and C, connect A and B), the  lamp 1 is off
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for  1- 2 seconds; signal LED on the receiver is on. The receiver enters into status  of LEARNING.
2) Press any one button on transmitter. If  signal LED flashes quickly 15 times and turns off, it means learning is  successful.
3) When receiver is in the status of LEARNING,  press again the button of receiver, signal LED turns off, learning process will  be discontinued.
4) The receiver can learn several remote  controls with different codes.
Delete all transmitters:
We have learned remote control to the  receiver. If you don’t want the receiver to work with the remote control, you  can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the button of  receiver until signal LED flashes slowly; release the button, LED keeps slow  flash. That means all stored codes have been deleted successfully.
Shipping:
Shipping methods: Ship to Worldwide by Airmail.
Delivery time: 10~25 working days (not including week-end and holiday).
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
We will inform you via Email when shipping your items.
Guarantee:
Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.