2 CH AC 12V/24V Power Output Waterproof Case Wireless Control System

Description

0020051
2 CH  AC 12V/24V Power Output Waterproof Case Wireless Control System - Receiver &  Transmitter
Model:  0020051
Package  Include:
1 x Receiver: S2X-AC12
1 x Transmitter: CWB-2
1 x User manual
Feature:
Application: It can be used in industry automation, agriculture automation and  home automation, such as factory, house, farm, pasture, vehicle, ship, offshore  operation, aerial vehicle, field call, etc. It can remote control equipments on  land, water and air, such as remote control lights, sirens, locks, motors, fans,  winches, blinds, linear actuators, doors, windows, electric solenoid valves,  security alarm, business signs and various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be  installed outdoors.
AC Power Output: It can control AC equipment with voltage 12V / 24V AC.
With wired control terminals: You can connect sensors, limit switches, manual  switches or external devices to control the receiver.
You can turn on/ off the receiver with transmitter (remote control) from any  place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same  code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No.: S2X-AC12
Power Supply (Operating Voltage): AC12~24V
Output: AC12~24V
Working Frequency: 433MHz
Channel: 2 CH
Control Modes: Toggle, Momentary, Latched
Static Current: ≤6mA
Maximum Working Current: 10A / each channel
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Work with Fixed code transmitters or Learning code transmitters.
Product  Description:
Model No.: 0021093 (CWB-2)
Waterproof
Shell Color: Black
Channel/Button: 2
Button Symbol: A, B
Operating Voltage: 6V (2 x CR2016 -3V button cell batteries, can be used for 12  months)
Operating Current: 5mA
Operating Frequency: 433Mhz
Encoding Chip: PT2260/ PT2262 / PT2264
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 50m / 150ft (theoretically)
The distance of 50m is a theoretical data, it shall be operated in an open  ground, no barriers, no any interference. But in the practice, it will be  hindered by trees, walls or other constructions, and will be exposed to some  interference by other signals. Therefore, the actual distance may or may not  reach 50m.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 56mm x 32mm x 12mm
Weight: 20g
Uses: garage doors, motorcycles, car alarm products, home security products,  wireless remote control products, industrial control products.
Matching Transmitters:
The receiver can work with different transmitters, such as model C-2 /  C-3(100M), CWB-2 / CWB-3 (50M, waterproof), CP-2 (500M), or CB-2 / CB-3 (1000M)  etc.
When you set the receiver in toggle or momentary mode, it should work with two  buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2  (500M), or CB-2 (1000M) etc. When you set the receiver in latched mode, it  should work with three buttons transmitter, such as model C-3 (100M), CWB-3  (50M, waterproof), or CB-3 (1000M) etc.
Working Range:
With a transmitter (such as CWB-2) to form a complete set, the maximum working  distance can reach 50M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an  open ground, no barriers, no any interference. But in the practice, it will be  hindered by trees, walls or other constructions, and will be interfered by other  wireless signals. Therefore, the actual distance may not reach this maximum  working distance.
If you want to have a further working range, you can install an external antenna  to the receiver, and you also can use a powerful transmitter, such as CB series  transmitters.
Usage (with the transmitter CWB-2):
The receiver can be used to control AC12~24V equipments.
Wiring:
If you want to control an AC12V lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L / +” of INPUT, and  connect the neutral wire of AC power supply to terminal “N / -” of INPUT.
2) Connect one side of AC lamp to terminal "L / +" of OUTPUT, and connect  another side of AC lamp to terminal "N / -" of OUTPUT.
Setting  different control modes:
Setting different control modes: (We have set the receiver in toggle mode before  delivery, if you want to use other modes, do as following operation.)
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (with transmitter CWB-2): Press -> On; Press again -> Off.
Press button A of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1  is on.
Press button A again: Terminals “OUT1” stops outputting, the lamp 1 is off.
Press button B of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2  is on.
Press button B again: Terminals “OUT2” stops outputting, the lamp 2 is off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with transmitter CWB-2): Press and hold -> On; Release  -> Off.
Press and hold button A of the transmitter: Terminals “OUT1” outputs AC power,  the lamp 1 is on.
Release button A of the transmitter: Terminals “OUT1” stops outputting, the lamp  1 is off.
Press and hold button B of the transmitter: Terminals “OUT2” outputs AC power,  the lamp 2 is on.
Release button B of the transmitter: Terminals “OUT2” stops outputting, the lamp  2 is off.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched (with transmitter CWB-3): Press -> On, Press another button  -> Off.
Press button B of the transmitter: Terminals “OUT1” outputs AC power, the lamp 1  is on.
Press button C of the transmitter: Terminals “OUT2” outputs AC power, the lamp 2  is on.
Terminals “OUT1” stops outputting, the lamp 1 is off.
Press button A of the transmitter: Terminals “OUT2” stops outputting, the lamp 2  is off.
Wired control terminals:
The receiver has manual control terminals, you can connect external devices,  sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual  terminals 1 (Signal +), terminal 2 (Signal +) and terminal 3 (Signal -) , then  the external device’s output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and  terminal 3, turns on the relay 1. Terminals “OUT1” outputs AC power, the lamp 1  is on.
When the external device stops to output signal, turns off the relay 1.  Terminals “OUT1” stops outputting, the lamp 1 is off.
When the external device outputs low level signal to manual terminal 2 and  terminal 3, turns on the relay 2. Terminals “OUT2” outputs AC power, the lamp 2  is on.
When the external device stops to output signal, turns off the relay 2.  Terminals “OUT2” stops outputting, the lamp 2 is off.
2) The manual switches:
You can connect manual switches to manual terminals 1, 2 and 3, then you can use  manual switches to control the receiver.
When connect terminals 1 and 3, turns on the relay 1. Terminals “OUT1” outputs  AC power, the lamp 1 is on.
And when disconnect terminals 1 and 3, turns off the relay 1. Terminals “OUT1”  stops outputting, the lamp 1 is off.
When connect terminals 2 and 3, turns on the relay 2. Terminals “OUT2” outputs  AC power, the lamp 2 is on.
And when disconnect terminals 2 and 3, turns off the relay 2. Terminals “OUT2”  stops outputting, the lamp 2 is off.