30A 1CH 110V 220V Wireless RF Toggle Remote Control - Transmitter & Receiver

Description

0020412
30A 1CH  110V 220V Wireless RF Toggle Remote Control -  Transmitter & Receiver
Model: 0020015
This 1 channel wireless rf remote control  operates in the 315/433MHz frequency. Just press slightly  the button on the remote, you can control on/off, open/close  of universal electrical devices. Applications include light  remote control, electric gate remote control, electric  window / blind remote control, etc.
Package  Include:
1 x Receiver: S1PT-AC220 (1 Channel / Toggle  Control Mode)
2 x Transmitter: C-1
1 x
User manual
Feature:
Application: It can be used in industry automation, agriculture automation and  home automation, such as factory, house, farm, pasture, vehicle, ship, offshore  operation, aerial vehicle, field call, etc. It can remote control equipments on  land, water and air, such as remote control lights, sirens, locks, motors, fans,  winches, blinds, linear actuators, doors, windows, electric solenoid valves,  security alarm, business signs and various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be  installed outdoors.
Universal input: Support voltage of AC110V (100V~120V), widely used in US,  Canada... and voltage of AC220V (200V~240V), used in UK, France...
Relay Output: This receiver is relay output, it can be used to operate both DC  and AC equipments. The terminal is NO / NC (normally open / normally closed),  which serves as a switch. That means you should also connect a separate power  supply to it.
High Power: Each channel can work at maximum current 30A, such as 360W/12V,  180W/6V, 270W/9V, 720W/24V, 3000W/110V, 6000W/220V.
With wired control terminals: You can connect sensors, limit switches, manual  switches or external devices to control the receiver.
Design with low-power and high-speed CMOS technology.
You can turn on/ off the receiver with transmitter (remote control) from any  place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same  code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No. S1PT-AC220
Power Supply (Operating Voltage): AC100~240V  (110V/120V/220V/240V)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Working Frequency: 315MHz / 433MHz
Channel: 1CH
Control Modes: Toggle (Press -> On; Press again -> Off)
Static Current: ≤6mA
Maximum Working Current: 30A
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Work with Fixed code transmitters or Learning code transmitters.
Transmitter Parameters:
Model No.: C-1
Channel: 1 CH
Remote Control Distance: 100m / 300ft (theoretically)
Encode: Fixed code by soldering
Unit size: 58mm x 39mm x 16mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Matching Transmitters:
The receiver can work with different transmitters, such as model C-1 (100M),  CWB-1 (50M, waterproof), CP-1 (500M), or CB-1 (1000M) etc.
Usage (with the transmitter like C-1):
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state of  relay output terminals: Terminals B and C are Normally Open; Terminals A and C  are Normally Closed.
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L / +”, and connect the  neutral wire of AC power supply to terminal “N / -”.
2) Connect terminal B to the positive pole of DC power supply, connect terminal  C to the positive pole of DC lamp, and connect the negative pole of DC lamp to  the negative pole of DC power supply.
If you want to control an AC 220V lamp, do as following:
1) Connect the live wire of AC power supply to terminal “L / +”, and connect the  neutral wire of AC power supply to terminal “N / -”.
2) Connect terminal B to the live wire of AC power supply, connect terminal C to  one side of AC lamp, and connect another side of AC lamp to the neutral wire of  AC power supply.
Control modes:
Control mode Toggle: Press -> On; Press again -> Off.
Press button of transmitter: Turn on the relay (connect B and C, disconnect A  and C)
Press button of transmitter: Turn off the relay (disconnect B and C, connect A  and C)
Wired control terminals:
The receiver has manual control terminals, you can connect external devices,  sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual  terminals 1 (Signal -) and terminal 2 (Signal +), then the external device’s  output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and  terminal 2, the receiver turns on the relay. (connect B and C, disconnect A and  C)
When the external device stops to output signal, the receiver turns off the  relay. (disconnect B and C, connect A and C).
2) The manual switches:
You can connect manual switch to terminals 1 and 2, and then you can use this  manual switch to control the receiver.
When connect terminals 1 and 2, the receiver turns on the relay. (connect B and  C, disconnect A and C).
And when disconnect terminals 1 and 2, the receiver turns off the relay.  (disconnect B and C, connect A and C).
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the  receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times  and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of  receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to the receiver. If you don’t want the receiver  to work with the remote control, you can delete all codes of remote controls,  which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes  slowly; release the button, LED keeps slow flash. That means all stored codes  have been deleted successfully.
Shipping:
Shipping methods: Ship to Worldwide by Airmail.
Delivery time: 10~25 working days (not including week-end and holiday).
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
We will inform you via Email when shipping your items.
Guarantee:
Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.